ESPHome - конфигурация JetHub E1-PD76-R5-[AC/DC] (v3)

Конфигурация контроллеров JetHub E1-PD76-R5-AC (v3) и JetHub E1-PD76-R5-DC (v3) для ESPHome.

Note

Для сборки прошивки для контроллеров JetHub E1-PD76-R5-[AC/DC] (v3) необходимо использовать версии ESPHome 2023.11.0 или более новые, в которые была включена поддержка расширителей портов PCA9535 и аналогичных.

Configuration

This configuration implements:

  • Setting up Ethernet with automatic IP address detection.

  • Integration with Home Assistant.

  • Setting the LEDs STAT (red and green).

  • Настройка реле.

  • Event detection from the FN button .

  • Detection of events from all discrete inputs.

  • 1-wire bus.

Note

Once the controller is loaded and the IP address is obtained, the controller will automatically be available on the Home Assistant running on the same network.

Hint

Скачать jethub_e1_pd76_r5_v3.yaml

jethub_e1_pd76_r5_v3.yaml
  1esphome:
  2  name: e1-pd76-r5-v3
  3  platform: ESP32
  4  board: nodemcu-32s
  5  name_add_mac_suffix: true # This option adds MAC address to the end of the device name
  6
  7## WARNING: Disable WiFi and captive_portal if Ethernet enabled
  8#wifi:
  9#  ssid: "***"
 10#  password: "***"
 11#
 12#  # Enable fallback hotspot (captive portal) in case wifi connection fails
 13#  ap:
 14#    ssid: "JetHub E1 Fallback Hotspot"
 15#    password: "***"
 16#
 17#captive_portal:
 18
 19# Enable Ethernet
 20ethernet:
 21  type: LAN8720
 22  mdc_pin: GPIO23
 23  mdio_pin: GPIO18
 24  clk_mode: GPIO17_OUT
 25  phy_addr: 1
 26
 27# Enable logging
 28logger:
 29
 30# Enable Home Assistant API
 31api:
 32
 33# Enable OTA firmware update
 34ota:
 35
 36# Enable internal WEB server
 37web_server:
 38  port: 80
 39
 40# Enable I2C bus
 41i2c:
 42  sda: 5
 43  scl: 4
 44  frequency: 400kHz
 45  scan: true
 46  id: i2c1
 47
 48# Enable UART1
 49uart:
 50  - tx_pin: 33
 51    rx_pin: 34
 52    baud_rate: 115200
 53    id: uart_1
 54
 55# Enable I2C GPIO expanders
 56pca9554:
 57  - id: cpu_gpio_exp
 58    pin_count: 16
 59    address: 0x20
 60  - id: mb_gpio_exp
 61    pin_count: 16
 62    address: 0x22
 63
 64# Enable digital outputs: LEDs and relays
 65switch:
 66  - platform: gpio
 67    name: "Red LED"
 68    id: red_led
 69    pin:
 70      pca9554: cpu_gpio_exp
 71      number: 0
 72      mode: OUTPUT
 73      inverted: false
 74  - platform: gpio
 75    name: "Green LED"
 76    id: green_led
 77    pin:
 78      pca9554: cpu_gpio_exp
 79      number: 1
 80      mode: OUTPUT
 81      inverted: false
 82  - platform: gpio
 83    name: "Relay 1"
 84    id: relay_1
 85    pin:
 86      pca9554: mb_gpio_exp
 87      number: 8
 88      mode: OUTPUT
 89      inverted: false
 90  - platform: gpio
 91    name: "Relay 2"
 92    id: relay_2
 93    pin:
 94      pca9554: mb_gpio_exp
 95      number: 9
 96      mode: OUTPUT
 97      inverted: false
 98  - platform: gpio
 99    name: "Relay 3"
100    id: relay_3
101    pin:
102      pca9554: mb_gpio_exp
103      number: 10
104      mode: OUTPUT
105      inverted: false
106  - platform: gpio
107    name: "Relay 4"
108    id: relay_4
109    pin:
110      pca9554: mb_gpio_exp
111      number: 11
112      mode: OUTPUT
113      inverted: false
114  - platform: gpio
115    name: "Relay 5"
116    id: relay_5
117    pin:
118      pca9554: mb_gpio_exp
119      number: 12
120      mode: OUTPUT
121      inverted: false
122
123# Enable inputs: button and discrete inputs
124binary_sensor:
125  - platform: gpio
126    name: "FN button"
127    pin:
128      number: 0
129      inverted: true
130  - platform: gpio
131    name: "Input 1"
132    pin:
133      pca9554: mb_gpio_exp
134      number: 0
135      inverted: false
136  - platform: gpio
137    name: "Input 2"
138    pin:
139      pca9554: mb_gpio_exp
140      number: 1
141      inverted: false
142  - platform: gpio
143    name: "Input 3"
144    pin:
145      pca9554: mb_gpio_exp
146      number: 2
147      inverted: false
148  - platform: gpio
149    name: "Input 4"
150    pin:
151      pca9554: mb_gpio_exp
152      number: 3
153      inverted: false
154  - platform: gpio
155    name: "Input 5"
156    pin:
157      pca9554: mb_gpio_exp
158      number: 4
159      inverted: false
160  - platform: gpio
161    name: "Input 6"
162    pin:
163      pca9554: mb_gpio_exp
164      number: 5
165      inverted: false
166
167# Enable 1-Wire bus on external connector
168dallas:
169  - pin: 16
170
171## Configure individual sensors
172#sensor:
173#  - platform: dallas
174#    address: 0x1c0000031edd2a28
175#    name: "Livingroom Temperature"

Explanations

Note

This section describes explanations only for options that differ from the standard for the E1-CPU processor module.

Расширитель портов

В контроллере JetHub E1-PD76-R5-[AC/DC] (v3) используются микросхемы расширителя портов PCA9535. Для них можно использовать драйвер pca9554:

# Enable I2C GPIO expanders
pca9554:
  - id: cpu_gpio_exp
    pin_count: 16
    address: 0x20
  - id: mb_gpio_exp
    pin_count: 16
    address: 0x22

Relay

The relays are connected to the port expander on the peripheral board.

Для управления реле используется прямая логика:

# Enable digital outputs: LEDs and relays
switch:
  - platform: gpio
    name: "Relay 1"
    id: relay_1
    pin:
      pca9554: mb_gpio_exp
      number: 8
      mode: OUTPUT
      inverted: false
  - platform: gpio
    name: "Relay 2"
    id: relay_2
    pin:
      pca9554: mb_gpio_exp
      number: 9
      mode: OUTPUT
      inverted: false
  - platform: gpio
    name: "Relay 3"
    id: relay_3
    pin:
      pca9554: mb_gpio_exp
      number: 10
      mode: OUTPUT
      inverted: false
  - platform: gpio
    name: "Relay 4"
    id: relay_4
    pin:
      pca9554: mb_gpio_exp
      number: 11
      mode: OUTPUT
      inverted: false
  - platform: gpio
    name: "Relay 5"
    id: relay_5
    pin:
      pca9554: mb_gpio_exp
      number: 12
      mode: OUTPUT
      inverted: false

Note

When you change the state of the outputs, after some time (~40 sec) ESPHome automatically saves their state by default and after reboot restores the state of the outputs to the previously saved.

If this functionality is not needed, you must change this function by setting the output state at startup with the option restore_mode, for example:

switch:
  - platform: gpio
    ...
    restore_mode: ALWAYS_OFF
    ...

Discrete inputs

The digital inputs are connected to the port expander on the peripheral board.

Example of a digital input configuration:

# Enable inputs: button and discrete inputs
binary_sensor:
  - platform: gpio
    name: "Input 1"
    pin:
      pca9554: mb_gpio_exp
      number: 0
      inverted: false
  - platform: gpio
    name: "Input 2"
    pin:
      pca9554: mb_gpio_exp
      number: 1
      inverted: false
  - platform: gpio
    name: "Input 3"
    pin:
      pca9554: mb_gpio_exp
      number: 2
      inverted: false
  - platform: gpio
    name: "Input 4"
    pin:
      pca9554: mb_gpio_exp
      number: 3
      inverted: false
  - platform: gpio
    name: "Input 5"
    pin:
      pca9554: mb_gpio_exp
      number: 4
      inverted: false
  - platform: gpio
    name: "Input 6"
    pin:
      pca9554: mb_gpio_exp
      number: 5
      inverted: false

1-Wire

The 1-Wire bus is connected to pin GPIO16 of the microcontroller.

Enable 1-Wire bus in the configuration file:

# Enable 1-Wire bus on external connector
dallas:
  - pin: 16

Note

For each temperature sensor connected to the bus, you must add to the configuration file:

sensor:
  - platform: onewire
    address: 0x28XXXXXXXXXXXXXX
    name: "Livingroom Temperature"

where 0x28XXXXXXXXXXXXXX is the address of the temperature sensor.